Study of metal-loaded activated charcoals for the separation and determination of selenium species by energy dispersive X-ray fluorescence analysis

Conversion of adsorption properties of activated charcoal (C^∗) by metal modification towards selenite, selenate and seleno-dl-methionine (Se-Met) was studied. Several metals were included in modification studies and also a procedure was developed for the separation and independent determination of microgram quantities of these selenium species in aqueous solution. Selenium species were collected one by one from the same sample solution onto collector material by adsorbing them directly or after complex formation onto different metal-loaded activated charcoals (MgC^∗ and FeC^∗). The mass of selenium in these collectors was measured directly by energy dispersive X-ray fluorescence spectrometry (EDXRF). Detection limits for all three selenium species were better than 6 μg corresponding to concentration of 60 μg/l with 0.100 l of initial sample volume.     

焙烧富集分离－氢化物原子荧光法测定地质物料中痕量硒

本文研究了一种焙烧富集分离、氢化物－原子荧光法测定地质物料中痕量Ｓｅ的方法。系统地研究了Ｓｅ富集分离条件、考查了３０多种元素在焙烧前后对测定Ｓｅ的影响，在选定的最佳实验条件下，方法检出下限为０．０１μｇ／ｇ，线性范围为０．００１～０．３μｇ／ｍＬ。样品中Ｓｅ含量水平为０．０３６μｇ／ｇ和０．０８９μｇ／ｇ时的测量精度（ＲＳＤ）分别为１０％和５．８％。加标回收率为９７～９９％。采用本方法分析了２６个地球化学标准参考样中痕量硒，获得满意结果。     

Determination of manganese in brain samples by slurry sampling graphite furnace atomic absorption spectrometry

A simple procedure for the determination of manganese in different sections of human brain samples by graphite furnace atomic absorption spectrometry has been developed. Brain sections included cerebellum, hypothalamus, frontal cortex, vermix and encephalic trunk. Two sample preparation procedures were evaluated, namely, slurry sampling and microwave-assisted acid digestion. Brain slurries (2% w/v) could be prepared in distilled, de-ionized water, with good stability for up to 30 min. Brain samples were also digested in a domestic microwave oven using 5 ml of concentrated HNO₃. A mixed palladium+magnesium nitrate chemical modifier was used for thermal stabilization of the analyte in the electrothermal atomizer up to pyrolysis temperatures of 1300 °C, irrespective of the matrix. Quantitation of manganese was conducted in both cases by means of aqueous standards calibration. The detection limits were 0.3 and 0.4 ng ml⁻¹ for the slurry and the digested samples, respectively. The accuracy of the procedure was checked by comparing the results obtained in the analysis of slurries and digested brain samples, and by analysis of the NIST Bovine Liver standard reference material (SRM 1577a). The ease of slurry preparation, together with the conventional set of analytical and instrumental conditions selected for the determination of manganese make such methodology suitable for routine clinical applications.     

光度分析法测定痕量硒的研究与应用

就目前研究较多的测定痕量硒的光度分析法进行了综述,着重介绍了分光光度法、荧光光度法、散射光谱法、原子吸收光谱法、电感耦合等离子体发射光谱等方法.     

Structure inhomogeneities of medium-range order in fluorozirconate glasses

Images of cleaved surfaces were obtained for 53ZrF₄-20BaF₂-4LaF₃-3AlF₃-20NaF (ZBLAN) glasses and fused quartz using an NTMDT atomic force microscope. It is shown that the scatter of particle size depends on the cooling rate and is 21–48.5 Å for the cleaved surface of ZBLAN glass obtained by very fast cooling and 68–172 Å for the cleaved surface of ZBLAN after slow cooling. For cleaved fused quartz, the range is 25-18 Å.     

Slurry nebulization ICP-AES spectrometry method for the determination of tin in organotin(IV) complexes

This paper proposes a quick, novel method for tin determination in organotin chemicals by slurry nebulization inductively coupled plasma atomic emission (ICP-AES) spectrometry. The method was tested by the measurement of five organotin carboxylate complexes of known composition for obtaining simple stoichiometric data. The slurries were prepared by first dissolving the organotins in an adequate solvent (methanol, pyridine or acetone) well miscible with water and then adding this solution drop-by-drop to a 0.005% TX-100 tenzide solution while maintaining intensive mixing. Dynamic laser light scattering experiments showed that the average equivalent particle size in the resulting slurry was ≈0.3 μm for all samples and solvents. Under suitable ICP-AES measuring conditions, the signal recoveries were found to be between 101.8 and 106.6%, which allowed direct nebulization and calibration against aqueous solutions. Typically, 70 μg l⁻¹ detection limit and 1–5% relative S.D. on five replicates can be achieved by the described method.     

Determination of boron in boron-alloyed steels by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) procedure has been developed and examined for the determination of boron content (0.01 up to about 2% B) in boron-alloyed steels such as POLDI ATA BOR (65% Fe, 19%Cr, 12% Ni, 1.5% Mn, 1% B), POLDI ATA BOR EXTRA (62% Fe, 18% Cr, 13% Ni, 2.5% Mo, 1.5% Mn, 1% B) and POLDI ATA BOR-R (75% Fe, 18% Cr, 3.5% Ti, 1.8% B). The steel sample is dissolved with a mixture of hydrochloric, nitric, sulfuric and phosphoric acids in a quartz vessel. Borides of alloyed metals, especially of iron and chromium, are quantitatively decomposed. The presence of phosphoric acid in a sample solution reduces the volatility of boric acid with water vapour.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Sequential determination of platinum, ruthenium, and molybdenum in carbon-supported Pt, PtRu, and PtMo catalysts by atomic absorption spectrometry

A simple accurate and precise analytical method for the determination of platinum, ruthenium, and molybdenum in Pt, PtRu, and PtMo nanoparticles catalysts deposited on high-surface area carbon by flame atomic absorption spectrometry (FAAS) and graphite furnace atomic absorption spectrometry (GFAAS) is described. The complete digestion of samples (0.010-0.020 g), which contain noble metals (NMs) in the range between 0 and 30% in combination among them or with other non-NMs, is obtained under mild conditions using both concentrated HCl and HCl+HNO₃ (1+1 (v/v)) mixture to boiling for 30 min in an open vessel. Carbon is separated from the solution by filtering it. Under optimized conditions of the flame, the poor sensitivity of platinum is enhanced 50-fold in presence of 1% (m V⁻¹) ascorbic acid, whereas the analytical signal of ruthenium increased by the presence of co-existing platinum. Any kind of interference is observed on the analytical signal of molybdenum. Recovery test obtained by analyzing commercial powder catalysts ranged from 99 to 101%. The precision, expressed as relative standard deviation of five measurements, is better than 1%. Electrode catalysts, made by using the carbon-supported platinum-based powder catalysts, have been analyzed for the metal loadings onto the electrode by GFAAS after dissolution under the same conditions used for the powder catalysts. The precision, expressed as relative standard deviation of three measurements, is better than 2%.     

Determination of trace elements in biological materials using tetramethylammonium hydroxide for sample preparation

A method to prepare milk powder, bovine liver and bovine muscle samples for analysis by electrothermal atomic absorption spectrometry (ETAAS) is proposed. Samples are mixed with a small amount of tetramethylammonium hydroxide (TMAH) and a stable and homogeneous slurry is produced in ca. 2 h with heating at 60–70 °C. After such sample preparation and dilution with water, trace elements are determined in certified reference materials. Pyrolysis and atomisation temperatures are optimised for each element, and several modifiers are investigated. External calibration is used for every analyte. Limits of detection (LODs), precision and accuracy are reported for Cd, Pb, Ni, Cr, Cu and Ag and compared with those obtained after conventional acid digestion. The main advantages of the proposed method are the simplicity of sample preparation and the longer lifetime of the graphite tube.     

Electron-density-dependent fused-sphere surfaces derived from pseudopotential calculations

Fused-sphere surfaces can be used to mimic a molecular boundary associated with a constant value of the electron density. The simplest of such fused-sphere models are constructed by using the atomic radii for the spherical isodensity surfaces of individual atoms. In this work, we discuss the extension of this model to molecules containing atoms beyond the second row. In these many- electron systems, the computation of electron densities is usually simplified by adopting a pseudopotential (or effective-core potential) approach. Here, we discuss the performance of large- and small-core pseudo-potential calculations as a tool to derive atomic radii. Our results provide an optimum set of variable radii that can be used to build fused-sphere surfaces. This continuum of surfaces provides a simple approximation to the low-electron-density regions around molecules with heavy atoms.